Difference between revisions of "Pre-Flight Guide – Before Leaving For Field"

From Poland Lab Wiki
Jump to: navigation, search
(1. Flight Checklists)
m (1. Flight Checklists)
Line 10: Line 10:
 
               ❏ Radio with USB cable
 
               ❏ Radio with USB cable
 
               ❏ UAV batteries and battery chargers
 
               ❏ UAV batteries and battery chargers
               ❏ Propellers and extra propellers
+
               ❏ Extra set of propellers/wings
 
               ❏ Tool kit (wrench set, propeller hex-key, camera mount screws and screw driver etc.)
 
               ❏ Tool kit (wrench set, propeller hex-key, camera mount screws and screw driver etc.)
               ❏ Gimbal
+
               ❏ Gimbal to balance the camera
 
               ❏ Camera(s) with fully charged batteries  
 
               ❏ Camera(s) with fully charged batteries  
 
               ❏ SD cards with CHDK installed
 
               ❏ SD cards with CHDK installed
               ❏ Voltmeter (optional)
+
               ❏ Multimeter (optional)
               ❏ Calibration reference panel and metal stand (optional)
+
               ❏ Color calibration panel (optional)
 
               ❏ Ground Control Points installed (optional)
 
               ❏ Ground Control Points installed (optional)
 
        
 
        
Line 22: Line 22:
 
                
 
                
 
               ❏ An updated version of Mission Planner Software is installed on the field laptop.  
 
               ❏ An updated version of Mission Planner Software is installed on the field laptop.  
               ❏ Has the field map been cached in the Mission Planner program ? Details on map caching procedure are discussed below in section x.x.  
+
               ❏ Has the field map been cached in the Mission Planner program? Details on map caching procedure are discussed below in section x.x.  
                 (Note: This step is required only once for each new phenotyping field.)
+
                 (Note: This step is required only once per phenotyping field.)
 
               ❏ Does RC Transmitter have enough voltage?  FrSky transmitter should have ≥ 9.4V charge.   
 
               ❏ Does RC Transmitter have enough voltage?  FrSky transmitter should have ≥ 9.4V charge.   
               ❏ Are UAV batteries charged? 3-cell batteries should charge to 12.6V.  
+
               ❏ Are UAV batteries charged? 3-cell batteries should charge upto 12.6V.  
 
               ❏ Is the laptop charged? Do you need/have a laptop charger?  
 
               ❏ Is the laptop charged? Do you need/have a laptop charger?  
 
               ❏ Ensure that you are familiar with the laws and regulations related to flying UAVs in your country/area. General laws in the United States  
 
               ❏ Ensure that you are familiar with the laws and regulations related to flying UAVs in your country/area. General laws in the United States  
 
                 require 400 Feet maximum height and within line-of-sight flying.  
 
                 require 400 Feet maximum height and within line-of-sight flying.  
 
               ❏ Make sure you have watched all the UAV manufacturer recommended tutorials before your first flight.   
 
               ❏ Make sure you have watched all the UAV manufacturer recommended tutorials before your first flight.   
               ❏ When first flying your IRIS+, make sure to fly it away from people and in an open area.   
+
               ❏ When first flying your IRIS+, make sure to fly it away from poplulated areas and only in an open area.   
               ❏ Before the first flight make sure to perform a compass calibration otherwise this could lead to a bad behaviour in GPS enabled modes. You can  
+
               ❏ Before the first flight, make sure to perform a compass calibration otherwise this could lead to a bad behavior in GPS enabled modes. You can  
 
                 perform the compass calibration through APM or Mission Planner programs following this youtube video[https://www.youtube.com/watch?v=oD9Z9IR2TNU].
 
                 perform the compass calibration through APM or Mission Planner programs following this youtube video[https://www.youtube.com/watch?v=oD9Z9IR2TNU].

Revision as of 10:08, 21 March 2016

1. Flight Checklists

  1.1. Preflight Checklist – Before Leaving for Field
      
      1.1.1. UAS accessory list
             
             ❏	Transmitter
             ❏	Radio with USB cable
             ❏	UAV batteries and battery chargers
             ❏	Extra set of propellers/wings
             ❏	Tool kit (wrench set, propeller hex-key, camera mount screws and screw driver etc.)
             ❏	Gimbal to balance the camera
             ❏	Camera(s) with fully charged batteries 
             ❏	SD cards with CHDK installed
             ❏	Multimeter (optional)
             ❏	Color calibration panel (optional)
             ❏	Ground Control Points installed (optional)
      
      1.1.2. Things to check before leaving for field
             
             ❏	An updated version of Mission Planner Software is installed on the field laptop. 
             ❏	Has the field map been cached in the Mission Planner program? Details on map caching procedure are discussed below in section x.x. 
               (Note: This step is required only once per phenotyping field.)
             ❏	Does RC Transmitter have enough voltage?  FrSky transmitter should have ≥ 9.4V charge.  
             ❏	Are UAV batteries charged? 3-cell batteries should charge upto 12.6V. 
             ❏	Is the laptop charged? Do you need/have a laptop charger? 
             ❏	Ensure that you are familiar with the laws and regulations related to flying UAVs in your country/area. General laws in the United States 
               require 400 Feet maximum height and within line-of-sight flying. 
             ❏	Make sure you have watched all the UAV manufacturer recommended tutorials before your first flight.  
             ❏	When first flying your IRIS+, make sure to fly it away from poplulated areas and only in an open area.  
             ❏	Before the first flight, make sure to perform a compass calibration otherwise this could lead to a bad behavior in GPS enabled modes. You can 
                perform the compass calibration through APM or Mission Planner programs following this youtube video[1].